How to Reset Braemar Ducted Heating: A Quick Guide
If your Braemar ducted heating system suddenly stops and you see a fault code, it might be something as simple as a loose wire; or maybe a more serious broken part is the cause of the problem. Before you do anything, you should absolutely check for error messages, because they are what you need to investigate the issue.
No matter if you are dealing with inconsistent heating, a thermostat that is unresponsive or the dreaded blinking LED light on the heater unit, knowing how to reset Braemar ducted heating when the need arises will save you considerable time, money and discomfort.
You can attempt a simple reset for temporary glitches that sometimes occur following a power outage, or when the system isn’t working properly, but if you have reset your system several times and the fault persists, you have a more serious fault which requires the attention of an expert.
This guide walks you through exactly how to reset your Braemar ducted heating system properly, what common issues to troubleshoot, and when you will need to call in the experts. Backed by local experience, we’ve built this guide with real Australian homes in mind, based on what actual Braemar owners face daily.
Why You Might Need to Reset Your Braemar Ducted Heater
Your heater might suddenly stop working or show signs of trouble like:
- Not heating up at all.
- Blowing cold air.
- Flashing lights or error codes on the unit.
- Thermostat not responding.
- Heater cycles on and off repeatedly.
Most of the time, these issues can be cleared with a simple reset. However, it’s important to understand that resetting is not a fix-all solution. If there’s an underlying issue such as a faulty sensor, blocked duct, or gas problem, it might return shortly after the reset.
Reset Your Braemar Fast
How to Reset Braemar Ducted Heating: Step-by-Step guide
Step 1. Turn Off the System
- Locate your Spectrolink comfort controller (or the thermostat controlling your Braemar system).
- Press the ON/OFF button to turn the system off completely.
- Ensure the system is not running and has had a chance to cool down before proceeding.
Step 2. Check for Error Codes
- If there is a fault, the controller may display an error code or RESET message, often accompanied by a flashing light or fault number.
- Make a note of the error code displayed (this can help with troubleshooting later if the reset fails).
Step 3. Acknowledge the Fault
- Press the RESET button on the controller to acknowledge the fault. This clears the error from the controller’s memory.
- The heater will perform off and prepare for a reset.
Step 4. Perform the Reset
- After acknowledging the fault, press the RESET button again to initiate the reset process.
- Wait for a few moments as the system processes the reset command.
Step 5. Restart the System
- Once the reset is complete, turn the system back on by pressing the ON/OFF button.
- The heater will attempt to restart up normally. You may hear the fan or ignition clicking sounds during the process.
Step 6. Monitor the System
- Observe the system to ensure it starts up without issues.
- If the heating resumes and no fault codes appear, the reset has been successful.
Braemar Not Starting? Fix It
You Can Also Go With Other Simple Reset Methods…
Depending on the issue you’re facing, you may need to perform a basic power cycle or a more specific fault reset. Below are the correct procedures to reset your system safely in simple steps.
1. Basic Power Cycle Reset
This is the most common and first method you should try.
Steps:
- Turn off your heater using the wall thermostat or controller.
- Locate the main power switch for the unit. It’s usually near the indoor unit, outside the house, or inside the switchboard. Look for a red or black switch labeled “Heater” or “Braemar.”
- Switch the power off, then wait at least 30 seconds.
- Turn the switch back on.
- Wait 2–3 minutes for the system to boot. You might hear the blower fan or internal components clicking on.
- Turn the thermostat back on, and set it to your preferred temperature.
Tip: If your thermostat is battery-operated, this is a good time to check or replace the batteries.
2. Reset After a Fault Code or Lockout
If your unit is displaying LED flashes or error codes, it’s trying to tell you something. These often indicate a fault that temporarily disables the system to protect it.
Steps:
- Note the flashing pattern or error code. Some Braemar models blink in sequences to indicate the fault type.
- Turn off the heater at the thermostat.
- Turn off power at the wall or circuit breaker.
- Wait 60 seconds to let the internal capacitors discharge then restore power.
- Check if the flashing light or code returns.
- If it clears, great. If not, check the user manual or contact a licensed technician.
Note: Repeated lockouts usually indicate a more serious issue like a flame failure, blocked flue, or sensor malfunction.
3. Resetting the Thermostat or Controller
Sometimes the problem lies with the controller, not the heater itself. This is especially true with smart or programmable thermostats.
Steps:
- Remove the batteries (if applicable), wait 30 seconds, and reinstall them.
- Press the reset button, usually found in a pinhole labeled “Reset.”
- Switch the mode to “Off”, wait 30 seconds, and switch back to “Heat”.
- Reprogram your desired temperature and zones.
Warning: Factory resetting some thermostats may erase your schedule or zone settings, so proceed with caution.
Whole-Home Power Reset (Last Resort)
If resetting individual components doesn’t work, turn off your entire home’s power supply for 20–30 minutes. This fully clears the onboard memory, allowing a fresh system restart.
Why Resetting Works
Resetting clears stored errors and refreshes system power often resolves minor faults without needing repairs or replacements. After reset, your system usually restarts normally. But remember, resetting will clear any custom settings, so you may need to reprogram temperature preferences afterward.
Troubleshoot Heating Issues Easily
Common Braemar Ducted Heating Troubleshooting Issues
Resetting won’t always solve the problem, especially if something’s gone physically wrong with your unit. Here are a few things to check before or after attempting a reset:
1. Blocked or Dirty Filters
Clogged filters restrict airflow, which can cause the system to overheat and shut down.
- Remove and inspect return air filters.
- Clean with a vacuum or replace if necessary.
2. Closed or Obstructed Vents
Blocked vents can create airflow imbalance, triggering a safety shutdown.
- Ensure vents are fully open and unobstructed by furniture or rugs.
3. Gas Supply Issues
No gas = no heat.
- Check that your gas valve is open.
- Make sure you’ve paid your gas bill (you’d be surprised!).
- For LPG tanks, ensure there’s fuel remaining.
4. Faulty Flame Sensor or Igniter
If the unit tries to start but shuts off quickly, the flame sensor or ignition system may be failing.
This requires professional servicing.
5. Thermostat Malfunction
Faulty thermostats may not communicate properly with the unit.
- Try using a backup thermostat if available.
- Inspect wiring if you’re confident (or call an electrician).
When to Call a Professional
If you’ve tried all the steps above and the system still won’t operate or if it resets and fails again shortly after you likely have a deeper issue.
Call a licensed gas heating technician if:
- Persistent error codes after reset
- Repeated shutdowns or poor heating performance.
- You hear unusual noises from the ducting
- The fan runs but no heat comes out
- The thermostat won’t connect or displays an error
- You smell gas
- Any time you sense a safety concern.
Licensed professionals can test gas pressure, inspect burners, replace faulty sensors, and service internal components that DIY users shouldn’t touch.
Pro Maintenance Tips to Avoid Resets in the Future
To avoid frequent resets and extend your heater’s lifespan, regular maintenance is key.
- Clean filters every 1–2 months during peak use.
- Book a professional service once a year, especially before winter.
- Keep vents and return air grilles clear of obstructions.
- Ask your technician to check duct seals for leaks.
Key Takeaways
- Resetting Braemar ducted heating is a simple first step when your system stops working.
- Always try a power cycle before diving into fault codes.
- Repeated resets are a sign of a deeper issue, don’t ignore them.
- Clean filters and regular servicing go a long way toward keeping your system healthy.
- When in doubt, call a licensed technician, especially with gas appliances.
Final Thoughts
Your Braemar ducted heating system is designed to be durable and reliable, but like any gas appliance, it may occasionally require a reset or basic troubleshooting. Understanding how to reset Braemar ducted heating empowers you to solve minor issues yourself and avoid unnecessary service calls.
Still stuck? Don’t risk it especially with gas systems. Call a qualified technician to inspect and repair your unit safely.
FAQs
If your heater stops blowing warm air, flashes a fault light, or becomes unresponsive, it may need a reset. Power cycling is the first thing to try.
There’s typically no single “reset” button. You reset the system by turning the power off and back on at the main wall switch or breaker.
It’s a fault code. Count the number of flashes and refer to the model’s manual to interpret the issue. Repeated flashes usually mean a persistent fault.
Some models allow you to restart the system via the smart controller. However, if the unit has locked out due to a fault, you may still need to power cycle it manually.
There may be a deeper issue such as flame failure, dirty burners, or a faulty thermostat. Call a licensed technician to diagnose the cause.